E-Tech ET8 Manual de instalación descargar pdf (Pagina 10)

10

E-TECH ET8 (V4) CONTROL PANEL – INSTALLER MANUAL

KEYPAD

Zone is sealed

Zone is unsealed, or Power fault

or System is Armed,

or phone line fault

Disarmed

Disarmed

Disarmed

Normal

Normal

Normal

Normal

Normal

Normal

Normal

Normal

Ready to Arm

Zone is unsealed

Ready to Arm

Armed (AREA 1)

Armed (AREA 2)

Monitor Mode

Memory Mode selected

Receiving radio signal

Dialler is on line

(And in Memory Mode indicates a

low battery alarm from a radio device)

Indicates that a Radio Key or

other radio device has a

low battery

Phone line fault or

failure to communicate

User Program Mode

Not ready to Arm

Zone alarm

Monitor Mode

(

LED Keypad only)

Mains Power is off

The panel’s backup

battery is low

New alarms in memory

Zones are excluded

Tamper alarm

Installer Program Mode

ZONES 1~8

ARMED

ARM2

MAINS

BATTERY

MEMORY

EXCLUDE

TAMPER

PROGRAM

LINE

READY

RADIO

Not Ready

OFF ON FLASHING

STATUS

LED KEYPAD LCD KEYPAD

2

5

8

0

1

4

7

P

3

6

9

E

ARM

MONITOR

EXCLUDE

MEMORY

Not Ready

Backlit LCD

icon display

PANIC buttons

PANIC buttons

“Not Ready” light

The “Not Ready” light is on when the panel is not ready to Arm.

i.e, a zone is unsealed, there may still be movement in the

premises or a door or window left open

ARM button

ARM button

MONITOR button

MONITOR button

EXCLUDE button

EXCLUDE button

PROGRAM button

ENTER button

MEMORY button

MEMORY button

LED KEYPAD LCD KEYPAD

PROGRAM button

Protective flap not shown

Protective flap not shown

ENTER button

PANIC

ARM

1

4

7

0

2

5

8

ENTER

3

6

9

MONITOR

EXCLUDE

PROGRAM

PANICMEMORY

105mm 90mm

150mm

135mm

ET8 KEYPAD

The ET8 control panel may be supplied

with either the LED keypad (100-192) or

the E-Tech LCD Keypad (100-667).

The keypad provides important visual

and audible indications and is the main

interface for operating and programming

the ET8 control panel.

NUMBER OF KEYPADS

Up to 3 LED and/or LCD keypads can

be connected to the ET8.

1 beep

3 beeps

1 long beep

10 beeps

10

Each key press

Valid command

Error

Mains Power is off

or

Panel Battery is low

KEYPAD BEEPER SOUNDS

KEYPAD INSTALLATION

· Unclip the top half of the keypad housing

by pushing the top clips down with a

small screwdriver and pulling the housing

forward.

· Screw the base of the keypad housing to

the wall using the 4 mounting holes

provided.

· Bring the 4 connecting wires to the

terminal block on the PCB on the rear of

the keypad housing.

· Connect the wires to the screw terminals

as per the wiring diagram shown in this

manual.

· Clip the top half onto the base by first

engaging the bottom clips and swinging

the top closed. Push hard to ensure the

clips engage.

· Attach the Zone list label on the inside of

the lid.

CABLE LENGTH

The maximum allowable cable length is

100m (total cable length to all keypads) .

DISPLAY TEST (LCD Keyad only)

To display all the keypad icons press and

hold the button for at least 2

seconds. All the icons will be on whilst

the button is held down.

Display Test can be activated at any time

either in operating mode or any program

mode.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 63 64

Comentarios a estos manuales

Sin comentarios